House Grants

VHF funds foundation repair as well as some new foundations.

• Foundations as part of major basement renovations may not be funded and will be reviewed on a case-by-case basis after all city permits are approved.
• Any foundation that raises the house will be considered on a case-by-case basis.
• Reconstruction of foundation skirting should replicate the original, including water table elements.

Download or print Foundations & Seismic Upgrade Requirements

VHF funds only exterior brick and masonry work. Make sure your contractor is familiar with historic masonry work.

• When rebuilding a chimney, reuse original bricks or stone wherever possible.
• Replacement bricks or stone, if required, should closely match the original in profile, colour, texture and size.
• Do not use soot-stained bricks on exterior.
• Cleaning or paint removal should be undertaken with the gentlest method possible.
• Media (e.g. sand) blasting and power washing are not acceptable.
• When repointing mortar joints, power tools are not recommended for use on vertical joints and considerable care is required for their use on horizontal joints.
• Strength, composition, colour, texture and profile of mortar joints or pointing should closely match original.
• Mortar should be weaker than the bricks. Historic brick construction used soft lime mortars with a minimum of Portland cement.
• Counter-flashing on brick chimney sides should include stepped (rather than continuous) and inserted into horizontal mortar joints and re-mortared. If previous counter-flashing was set into a diagonal groove cut into bricks, this must be repaired with colour-matched mortar.
• Profile and material of chimney cap and chimney pots should closely match original; try to find old photographs. Beware of reproducing a chimney that has been rebuilt incorrectly in previous years.
• If installing flue liners (not funded by VHF), use minimum projection above chimney.

Download or print Chimney, Masonry & Stucco Requirements

It is preferable to repair rather than replace original wood sash windows. The key to window longevity is the quality of the original material and construction techniques, combined with regular maintenance. These general guidelines for historic windows also apply to the repair, restoration and replication of historic doors.

• VHF funds repair and restoration of historic windows.
• VHF funds replication of historic windows where the original windows are missing or beyond repair.
• VHF does not fund double-glazed or thermal units.
• Replacement windows must replicate the original windows in material, overall frame size, sash profile and size, muntin profile and size, glass colour and reflective qualities.
• Replace windows with historically appropriate or vintage glass.
• Wood muntin bars separate pieces of glass. They are not placed over one large pane of glass.
• Loose and deteriorated window putty must be removed and replaced with linseed oil glazing putty. Linseed oil putty requires 2-4 weeks drying time before painting with oil or alkyd primer.
• It is recommended that visible hardware such as hinges, door handles, locks and escutcheons be appropriate to the period and style of the house.
• Modern weather stripping, door sweeps and deadbolts should be as unobtrusive as possible when viewed from the exterior.
• To be eligible for VHF funding, weatherstripping should be durable and not visibly alter the profile of the window/door or jamb. Some examples include:
  – Silicone tube seal set in a groove
  – Spring bronze
  – Interlocking metal

Recommended: Consider using historic “wavy” glass appropriate to the period of the house be used rather than modern float glass.
Storm Windows

Storm windows can increase the life of historic windows by providing protection from the elements as well as heat and sound insulation. To obtain the highest efficiency from a wood storm, the existing window should be well maintained, operable, tight fitting and retrofitted with weatherstripping.

• VHF funds fixed and opening traditionally-constructed (jointed with through-mortise and tenon joinery) wood storm windows.
• Storms must be attached with non-invasive hardware such as storm hangers.
• It is recommended that all storm hardware be attached with stainless steel screws.
• New storms must be primed on all sides and finish-painted before installation.
• Storms must be painted in gloss or semi-gloss paint the same colour as the exterior face of the sash underneath.
• No modifications, cutting, or alterations to the building’s character-defining elements are permitted during storm window installation.
• It is recommended for safety reasons for the storm windows to be openable from the interior.

Download or pring Windows, Doors & Storm Window Requirements

• Gutter replacement should be coordinated with re-roofing, and both should precede painting.
• Fascia boards and rafter tails should be checked for rot, and repairs included in quotes.
• Do not allow contractors to cut off the exposed or notched rafter tails (typically found on Craftsman houses) to allow installation of larger gutters.
• Do not allow contractors to cut into the water table when attaching downspouts.
• Built-in gutters should be repaired and retained rather than attaching new ones.
• When repairing or replacing deteriorated woodwork, use the same wood species (likely fir or cedar) as the original and ensure that the exact profile of the original material is replicated. (Most modern stock lumber has rounded edges and is likely smaller than the original and may not be an acceptable replacement).
• All new woodwork must be primed with alkyd (oil) primer on all sides at the time of installation.
• Original gutter and downspout materials are preferred (i.e. wood, galvanized metal), but pre-finished enameled steel or aluminum is acceptable if compatible with colour scheme of house.
• Original profile of gutters (typically ogee or K-style) and downspouts should be replicated.
• Downspouts in Victoria were typically round (3″ is available locally). Square downspouts will not be funded unless there is documentary evidence that they were original to the house.

Download or print Fascia, Gutters & Downspout Requirements

VHF funds repairs to historic stucco. VHF also funds removal of stucco, asphalt, asbestos, aluminum or vinyl siding where original siding has been covered by these materials.

• Ensure that any textured or decorative stucco is accurately recorded before undertaking repairs (i.e. note texture, thickness and colour).
• Strength, composition, colour and texture of historic stucco should be carefully matched.
• Consider repairing the entire wall panel or section, but generally do not remove sound stucco.

Download or print Chimney, Masonry & Stucco Requirements

When obtaining estimates for roofing, it is important to provide roofers with a copy of these VHF requirements and ensure that they specify the applicable requirements in their written quotes.

General Guidelines

• VHF funds repairs to roofing including flashing.
• VHF is able to fund re-roofing of a house once every 30 years
• VHF will fund re-roofing with historic material as well as compatible substitutes.
• Substitute roofing material should reflect the historic material in design, colour, exposure, size and other visual qualities. A sample of proposed material, if new to VHF, must be submitted for review and approval.
• Roofing and gutter replacement should be coordinated (see Fascia, Gutter & Downspout requirements).
• Masonry chimneys require repointing; this should be done prior to re-roofing (see Chimneys & Masonry requirements).
• Ensure that nail length for roof overhang on exposed eaves is correct to avoid protruding nails.
• All new elements (including vents) should be fitted as discreetly as possible.
• Vents must be installed to BC Building Code requirements. Contractor should indicate the number of required vents and discuss placement of the vents.
• Ensure chemical and physical compatibility between roofing material, fastenings and flashings (i.e. do not use copper with galvanized material).
• Low-pitched roofs have specific requirements: refer to BC Building Code or specialist.
• Original ridge capping may have been metal or wood and should be reinstated, if known.
  If there is documentation of original rooftop decoration or missing features such as cresting or finials, consider replacing at time of re-roofing (see Special Grants in Application Requirements document).

Download or print Roof Requirements

• It is always preferable to repair original material where feasible.
• Where the design of missing woodwork elements is unknown, documentary evidence must be provided from buildings of a similar style and era to demonstrate that replicated elements will be appropriate. To ensure historical accuracy, it is recommended that homeowners consult widely with those knowledgeable in the field before undertaking the replacement of missing elements (e.g. heritage architects, designers or engineers, City of Victoria Heritage Planners, VHF House Grants Inspectors). Such preparatory consultations can assist the homeowner in avoiding inaccurate design choices as well as the use of inappropriate materials.
• When repairing or replacing deteriorated woodwork, use like materials (wood species) and ensure that the exact profile of the original material is replicated. (Most modern stock lumber has rounded edges and is likely thinner than the original and may not be an acceptable replacement.)
• Rotted or structurally deteriorated woodwork must be repaired or replaced prior to applying paint.
• All new woodwork must be primed with alkyd (oil) primer on all sides at time of installation (including concealed areas such as stair treads, etc).
• Contemporary products suitable for preservation of deteriorated woodwork should be researched for your projects.
• Composite materials (e.g. plywood, OSB, fibre-cement board) should not be used for exterior cladding without prior VHF approval.
• Most original porches in Victoria between 1900-WWII were decked with Douglas fir tongue and groove flooring, with a standard visible floor width of approximately 3 1/2 inches and ran parallel to the slope. They should be replaced with like materials whenever possible..
• Stair treads should be bull-nosed; cove moulding under the treads may be historically correct for your house.

Download or print Woodwork & Trim Requirements

To qualify for VHF funding, all preparation and painting must be approved by the Master Painters & Decorators Association (MPDA).  MPDA provides project specifications and conducts inspections to ensure a high-quality, long-lasting paint job. The cost of the MPDA inspections should be separately itemized in the painter’s quotes.

The MPDA involvement is a contractual agreement between the homeowner and MPDA.  VHF will not mediate between homeowners and contractors and encourages direct communication.  No grant will be paid until the MPDA inspection fee is paid, the painting company is paid, and all deficiencies identified by MPDA are resolved.

When applying for a VHF grant, ensure painters are familiar with the MPDA Specifications and process when obtaining quotes. Refer to the links below for more information: 

Paint Requirements 2025

MPDA Technical Specifications (revised January 2023)

MPDA Request for Consultation 2024

MPDA – SSI009 – Request for Specification[28047] 11.2

MPDA Strata Request for Inspection – Dec 1 2024

MPDA Submittal Pages for MPDA Specification Paint

Paint
The following are general guidelines for painting a historic wood house:

• Exterior repairs should be completed before exterior painting: i.e. foundation, roofing, drainage, windows, woodwork and trim repairs.
• Woodwork repairs to rotten siding or window sills should be completed before painting.
• Loose or warped siding or shingles must be nailed flush with surface using appropriate nails.
• Loose or deteriorated window putty must be removed and replaced with linseed oil glazing putty. This will need to be done by others, as linseed oil putty requires several weeks drying time before alkyd/oil primer can be applied.
• Doors and trim molding are to be MPI Gloss level 5 or higher.
• Exterior painting should be done when air and surface temperatures remain above 10°C for at least 24 hours before, during and after paint application.
• Wood moisture content should not exceed 15%; use a moisture meter.
• No exterior painting should be done when the relative humidity is above 85% or when the dew point is less than 3°C variance between the air temperature.
• Downspouts and other removable hardware should be removed prior to painting and reinstalled upon completion.

The most important aspect of a paint job is preparation of the surface to be painted. An improperly prepared surface will not hold paint. If done correctly the first time, then maintenance will be less frequent and subsequently much easier.

• Proper safety procedures should be observed when removing existing paint or surface coatings.
• Remove damaged or deteriorated paint to the next sound layer using the gentlest method possible (scraping and sanding).
• No media (e.g. sand) blasting.
• No stripping by torch
• Ensure a clean surface, free of grease, dirt, mildew, etc. by washing wall surfaces, overhangs, porch ceilings and eavestroughs, inside and out, by hand with environment-friendly cleaners. Rinse thoroughly.
• Washing is acceptable by hand and garden hose.
• Crystalline deposits, which develop under eaves and protected areas, are a major cause of peeling; remove by washing and rinsing as above.
• Power washing historic wood is not recommended and should never be used as a means of removing paint.
• If power washing, ensure that the operator is experienced with historic wood and that low pressure below 600 psi is used.
• Water spray should always be directed downward and kept away from openings in the siding.
• House must dry between washing and painting to ensure the surface will not resist new paint. Wood moisture content should not exceed 15%; use a moisture meter.
• Areas of heavy paint buildup, alligatoring, blistering, scaling and peeling, or areas which show a moderate to heavy chalk deposit must be thoroughly prepared to ensure paint adhesion. Remove to a sound substrate by scraping, wire brushing and sanding.
• No grinding or heavy abrasive sanding that damages the wood surface.
• Glossy surfaces under eaves and protected areas that are not exposed to normal weathering should be dulled by sanding.
• Where bare wood is exposed, prime with a high quality alkyd (oil) primer.
• Loose or warped siding and shingles must be nailed flush with surface using appropriate nails.
• Fill all crevices, nail holes and cracks.
• All loose or split caulking is to be removed and replaced. Re-caulk with flexible, paintable caulking, and then prime.
• Do not apply paint in direct sunlight.

Paint Requirements 2025

Technical Specifications (revised January 2023)

MPDA Request for Consultation 2024

MPDA – SSI009 – Request for Specification[28047] 11.2

MPDA Strata Request for Inspection – Dec 1 2024

MPDA Submittal Pages for MPDA Specification Paint

• Shingle siding should be stained unless already painted.
• Stains penetrate the wood surface and are less likely to peel.
• On rough-sawn textured shingles, previously stained weathered surfaces must be thoroughly cleaned with a stiff fibre brush and a mild, biodegradable remover such as sodium hydroxide, to remove “dead” wood fibres.

• A minimum of two coats of top-quality paint should be applied; film thickness as per material specifications.
• Choice of paint will depend on condition of surface, the existing undercoat, location on house and design of house.
• Window sashes, doors, frames and trim must be done in gloss or semi-gloss.
• Doors and trim moldings are to be MPI Gloss level 5 or higher.
• Old stains in wood will leach through latex paint. Wood must be sealed with an alkyd (oil) primer.
• Half-timbering was likely meant to have a flat finish, to simulate an aged, medieval, rough-hewn look.

Changes to colour schemes require approval through a Delegated Heritage Alteration Permit (DHAP) from the City. This is an expedited process and there is no fee.

A historically-appropriate colour scheme approved for funding by VHF must be one of the following:

• Professionally-documented original colours.
• Historically-appropriate colour schemes. Please refer to Your Old House, True Colours and Historical True Colours for Western Canada for more information including correct colour placement. Be sure to understand what style your house is (e.g. Queen Anne, Italianate, Craftsman, etc.) when referring to these sources.

• Submit the following for consideration and approval by VHF:
• Copy of DHAP application submitted to the City if colours changed.
• Sketch or coloured-in photocopy illustrating colours and their placement on the architectural elements of the house.

If you are planning to paint the exterior of your house, you should be informed about the dangers of lead paint. Lead was common in exterior paint manufactured before 1990. You should assume that any home built before 1990 contains some lead paint. Lead in paint becomes a hazard when it is breathed in as dust created by sanding, grinding or cutting, or is otherwise ingested as chips, flakes or from residue rubbing off onto food through dusty/contaminated hands. You, your children, your neighbours and the workers can be exposed to lead any time you breathe lead dust, fumes, or swallow anything that contains lead. While lead in paint can be a serious danger, it can be safely removed.

Worksafe BC requires proper testing and procedures for handling and the disposal of lead paint. VHF will reimburse homeowners applying for a painting grant for lead testing by a qualified hazardous material testing company up to a cost of $250. This should be completed prior to obtaining quotes for painting. Please contact VHF for more info.

Painting Requirements 2025

Technical Specifications (revised January 2023)

MPDA Request for Consultation

MPDA – SSI009 – Request for Specification[28047] 11.2

MPDA Strata Request for Inspection

MPDA Submittal Pages for MPDA Specification Paint